How to Remove Wood Flooring From Concrete

We all know that one of the hardest things to do is remove wood flooring from concrete. It can seem daunting, but it doesn’t have to be daunting. Removing wood flooring from concrete can be daunting if you want to update your home flooring. But with the right tools and instructions, it’s a job you can do it!

This blog post will show you how to remove wood flooring from concrete using some effective methods. We’ll also provide some tips on how to protect your floors while you work. So read on for all the info you need to get started!

How to Remove Wood Flooring From Concrete

Summary: There are a few ways to remove wood flooring from concrete. One is to use a power drill and a concrete bit that is specifically designed for removing wood flooring. Another is to use a chisel or a saw to cut the flooring away.

10 Methods on How to Remove Wood Flooring From Concrete

There are several ways that you can remove wood flooring from concrete. We’ve listed some of the most effective methods below.

Method 1:  Use a Pry Bar and Hammer

Using a pry bar and hammer is the best method if you plan to remove your wood flooring but don’t want to damage the concrete underneath. First, use the pry bar to loosen the edges of the wood flooring. Once the edges are lifted, use the hammer to tap the flooring until it comes off the concrete gently. Finally,  use a chisel to remove any remaining nails or staples.

Method 2: Use a Heat Gun

If you are trying to remove glued-down wood flooring, then using a heat gun is the best method. First, heat the adhesive with the heat gun. Once the adhesive is melted, use a putty knife to scrape it off the concrete. After that, you can easily remove the wood flooring. Ensure the area is well ventilated when using the heat gun.

Method 3: Use a Circular Saw

If you are trying to remove screwed-down wood flooring, then using a circular saw is the best method. First, set the depth of the blade to be just barely above the wood flooring level. Second, make sure that the saw is unplugged before you begin.

Next, use a sharpie to mark where you will be cutting. Third, make sure that the line is completely straight. Finally, cut along the line with the circular saw. Once you have cut through the wood flooring, you can unscrew it and pull it up.

A Circular Saw

Method 4: Use a Floor Scraper

A floor scraper is a tool specifically designed to remove flooring material from concrete. It has a long, sharp blade that can quickly scrape away wood, vinyl, or other types of flooring. Hold the tool in your hand and push it across the floor to use a floor scraper. The blade will do all of the work for you.

You Can Check It Out To Clean Smoke Damage From Wood

If you’re removing a large amount of flooring, or if the flooring is particularly stubborn, you may need to use a power scraper. This type of tool is similar to a floor scraper but has a motor that makes it easier to remove stubborn material.

Wear gloves and safety glasses to protect yourself from flying debris when using a floor scraper. Also, be careful not to damage the concrete beneath the flooring. If you’re not careful, you could end up with a big mess.

Method 5: Use a Belt Sander

You can also use a belt sander if you’re trying to remove glued-down wood flooring. This tool will quickly and easily remove the flooring without damaging the concrete beneath it.

To use a belt sander, start by placing the sander on the floor. Then, turn it on and move it back and forth over the flooring. Be sure to keep the sander moving, so you don’t damage the concrete. Once you’ve removed all the wood floorings, vacuum up the debris and dispose of it properly. Then, clean the concrete with a damp mop or cloth.

Method 6: Use a Reciprocating Saw

This method is very effective but can be dangerous if you’re not careful. Instead, use a reciprocating saw to cut through the flooring, being sure to go slowly and carefully. You’ll need to make several passes with the saw to cut through the wood completely. Be sure to wear protective goggles and gloves while you’re working.

Use a Reciprocating Saw

Start by cutting a groove into the wood flooring. You can do this by setting the saw to a shallow depth and making a pass along the length of the board. Once you’ve cut a groove, increase the depth of the blade and make another pass.

Repeat this process until you’ve cut through the entire thickness of the board. After you’ve cut through the boards, use a pry bar to remove them from the floor. Start at one end of the board and work towards the other.

Repeat this process until all of the wood floorings have been removed.

Method 7: Use a Steam Mop

If you’re trying to remove tile flooring, you can use a steam mop to loosen the adhesive. Start by heating the floor in a tiny area. Then, use the steam mop to saturate the tile. Be sure to hold the steam mop close to the surface, so you don’t damage the tile. After a few minutes, you should be able to lift the tile with ease. If not, repeat the process until the adhesive is loosened.

Method 8: Use a Solvent

If you’re trying to remove parquet flooring glued down, you can use a solvent to loosen the adhesive. First, score the flooring surface with a utility knife to help the solvent penetrate. Then, apply the solvent to a rag and rub it over the adhesive.

You may need to let the solvent soak in for a few minutes before scrubbing. Finally, use a putty knife or scraper to remove the softened adhesive. Be sure to follow the instructions on the solvent’s label and wear gloves to protect your hands.

Method 9: Use Heat

If the adhesive is heat-sensitive, you can use a heat gun or hair dryer to soften it. Hold the heat gun about 6 inches (15 cm) away from the floor and move it back and forth over the adhesive. Alternatively, direct the stream of hot air from a hair dryer onto the adhesive. Once the adhesive is soft, you should be able to scrape it up with a putty knife or scraper.

Use a Heat Gun or Hair Dryer

Method 10: Use Boiling Water

Boiling water can also be used to soften adhesive so that it’s easier to remove. Pour a pot of boiling water onto the floor and let it sit for a few minutes. Then, use a putty knife or similar tool to scrape the softened adhesive.

You may need to repeat this process several times to remove all adhesives. Be careful not to spill boiling water on yourself, and ensure that the room is well ventilated, so you don’t breathe in any fumes from the heated adhesive.

You can also use a heat gun to soften the adhesive if you want to remove linoleum or vinyl flooring. However, be careful not to overheat the area, as this could damage the subfloor.

You can use a few different methods to remove wood flooring from concrete. The best way for you will depend on the type of flooring you’re removing and the condition of the concrete beneath. Be sure to follow all safety precautions while working and dispose of all debris properly.

You Can Check It Out To Stain Hardwood Floors Grey

Some Tips on How to Protect Your Floors While Remove Wood Flooring From Concrete

  1. Clear the area where you will be working. Remove any furniture or other items that could get in the way or be damaged during the project.
  2. Sweep or vacuum the floor to remove any dirt or debris that could scratch the surface while you work.
  3. Remove any baseboards or trim from the area to be worked on. This will make the job easier and help protect these items from damage.
  4. Place a drop cloth or other protective covering over any areas you do not want to damage during the project, such as carpeting or flooring adjacent to the area you will be working on.
  5. Start at one end of the room and work your way towards the door, so you can make a quick exit if necessary.
  6. Use a putty knife or other tool to pry up the edge of the wood flooring. Work slowly and carefully to avoid damaging the underlying concrete.
  7. Once you have lifted a section of the flooring, use a crowbar or similar tool to pry it up from the rest of the floor.
  8. Continue working this way until all the wood floorings have been removed.
  9. Inspect the concrete for any damage that may have occurred during the removal process. If necessary, patch any cracks or holes with a concrete repair compound.
  10. sweep or vacuum the floor again to remove debris before applying a new floor covering.
Vacuum the Floor


Removing wood flooring from concrete is not as difficult as it may seem. In fact, a few methods can be used to get the job done.

Now that you know how to remove wood flooring from concrete, you can tackle this project yourself using our easy steps. It may take some elbow grease, but it’s doable! And once it’s done, you will have a nice clean surface ready for your new floors.

Photo of author

Adrian Green

Adrian has been interested in woodworking since he was a child. His father had a woodworking shop, and Adrian would help him out and learn from him. He gained basic carpentry knowledge as well as an understanding of how to work hard and take care of business. He enjoys woodworking as a hobby. He loves the feeling of creating something with his own hands, and the satisfaction that comes from seeing his finished products used by others. So he started this blog to spread his passion and knowledge to those interested in DIY wood-working projects. He knows that with a little guidance and practice, anyone can create beautiful pieces of furniture or décor from scratch.

Leave a Comment