How to Recess a Door Hinge

Do you ever feel like your door hinges need a little extra security? Whether it be for cosmetic purposes or to improve the stability of the door, recessing a door hinge can help. 

How to Recess a Door Hinge

It can give any room an updated look and also work to protect little ones from pinching their fingers on sticking hinges as they pass. If this is something that interests you, read on! We’ll discuss what tools you will need and take step by step through how to recess a door hinge in some easy steps.

Should Door Hinges Be Recessed?

Recessing door hinges can be a great way to improve the security, longevity, and aesthetics of your door. It also helps protect furniture, walls, and other items that may be near the door from being damaged by the hinge. However, not all doors require recesses for their hinges.

If your hinges are located in a place where they could easily be tampered with, then recessing them is recommended. If you have a high-traffic door that will be opened and closed frequently, recesses can help reduce wear and tear on the hinges. Additionally, if you are looking for a more aesthetically pleasing look to your door, then recessing the hinges can also help create a more uniform look.

Finally, you may want to recess your door hinges if you live in an area with a lot of moisture and humidity. This can help protect the hinges from corroding or rusting over time due to increased exposure to water.

However, if your doors don’t need these benefits, then it may not be necessary to recess them at all. No matter what you decide to do, make sure you do your research to ensure that the recessing process is done properly. This will help maximize the benefits of recesses and ensure that the hinges remain secure and intact.

10 Methods on How to Recess a Door Hinge

1.  Use a Power Drill

The first method is to use a power drill. You will need to find the center of the hinge and then drill a hole that is slightly smaller than the hinge pin. Once you have drilled the hole, you can insert the hinge pin and tap it into place with a hammer. 

Find the Center of the Hinge

Be sure to keep the pin straight while hammering it in. You may need a punch or some other tool to make sure the pin goes in all the way. Make sure you drill the hole in a straight line so that the hinge is even when it is finished. Though drilling may seem intimidating, it is a relatively straightforward process.

2.  Use a Hand Drill

If you don’t have access to a power drill, you can use a hand drill. The same process applies as with the power drill, but it will take longer to drill the hole. You’ll want to ensure that you have the correct size drill bit for your door hinges. 

It’s best to measure the screws that came with the hinge and buy a drill bit that is slightly larger. This will ensure that the screws fit properly without any problem. When drilling, be sure to keep your hand steady and keep the drill at a 90-degree angle. This will ensure that you have an even recessed hole for the hinge screws. Make sure you drill deep enough so that the screws will be flush with the door.

3.  Use a Chisel

Another option is to use a chisel. You will need to find the center of the hinge and then mark it with a pencil. Next, use the chisel to create a recess for the hinge pin. Once you have created the recess, you can insert the hinge pin and tap it into place with a hammer. 

Mark It With a Pencil

Be sure to use a protective cloth or mat when using the hammer and chisel to prevent any potential damage. Once the pin is in place, you can then secure the hinge with screws. Try to use screws that are just long enough to securely fasten the hinge without protruding too much beyond the surface. This will ensure a neat and professional-looking finish.

4.  Use an Impact Driver

An impact driver can also be used to recess a door hinge. This type of power tool uses a hammering action to drive screws quickly into the door. Impact drivers are more powerful than standard drills and can recess hinges faster. 

Start by attaching the bit to the impact driver. Then, position the hinge on the door frame and use a drill bit that’s slightly smaller than the head of the screw you’ll use. Drill a pilot hole through the hinge and into the door frame. Next, attach the screw to the impact driver and set it to the desired setting.

5.  Use an Oscillating Tool

An oscillating tool can also be used to recess a door hinge. You will need to find the center of the hinge and then mark it with a pencil. Next, use the oscillating tool to create a recess for the hinge pin. 

Once you have created the recess, you can insert the hinge pin and tap it into place with a hammer. Be sure to use a sharp bit for the best results. Make sure that you do not over-cut or de-laminate any wood when creating the recess. Once you have finished, use a chisel and hammer to clean up any excess material in the surrounding area.

6. Use a Router

A router is another tool that can be used to recess a door hinge. For this step, you will need a router with a straight bit. To begin, set the depth of your bit and then slowly move the router along the edge of the door frame where you want to recess the hinge. Make sure to move in one direction only, alternating sides as needed. Once you have finished routing all four edges, use a chisel to remove any excess wood.

If necessary, you can use a file or sandpaper to smooth out the edges of the recess. Once completed, your door hinge should fit properly into the frame.

7.  Use a Template Guide

If you don’t have access to any power tools, you can also use a template guide to recess your door hinges. First, measure out where you want your hinges and mark them with a pencil or marker. Then attach the template guide to your drill bit and start drilling! The template guide will keep your drill bit in place as you drill, ensuring that the holes are the same size and depth. Be sure to stop when the drill bit reaches the depth you need. When finished, remove the template guide, and you’re done!

You Can Also Use a Template Guide

8.  Use an Angle Grinder

An angle grinder can also be used to recess a door hinge. It offers greater control over the amount of material being removed and can be used to create a precise edge. Start by using a chisel to remove any paint around the door hinge before using the angle grinder. 

Secure the hinge in position and adjust the depth of cut until you have achieved the desired recess. Be sure to wear safety goggles when operating an angle grinder. When finished, smooth the edges around the recess with a file or sandpaper. Follow all safety instructions when using an angle grinder.

9.  Use an Electric Router Table

An electric router table is another tool that can be used to recess a door hinge. You will need to find the center of the hinge and then mark it with a pencil. Next, use the router bit on your electric router table to create a recess for the hinge pin. Once you have created the recess, you can insert the hinge pin and tap it into place with a hammer.

10. Use a Deep Hole Drill Bit

If you don’t have access to any of the other tools or methods, you can also use a deep-hole drill bit to recess your door hinges. Measure out where you want your hinges and mark them with a pencil or marker. Attach the drill bit to your drill and start drilling! Once you have created the recess, you can insert the hinge pin and tap it into place with a hammer.

Measure Out Where You Want Your Hinges

These are some of the different methods that can be used to recess a door hinge. Depending on what tools and supplies you have available, one of these methods will work for you!

Conclusion

Applying pressure to the door with your palm as you work will give the screws something firm to bite into and help prevent stripping. If your hinge is extremely loose, you may need to remove it from the door and start over. 

Be sure to line up the new holes with those that are already in the door so that they’re evenly spaced. Thanks for reading, and we hope this has given you some inspiration on how to recess a door hinge!

Photo of author

Jennifer Branett

Leave a Comment