If you’re looking to add new drawers to your home or office, it’s important to use the right tools for the job. One of the most important tools for drawer construction is a Kreg drawer slide jig. This tool makes it easy to install drawer slides precisely and accurately.
In this blog post, we’ll show you how to use kreg drawer slide jig, so you can easily add new drawers. If you’re looking to add new drawers to your home décor, the Kreg drawer slide jig is the perfect tool! With this handy jig, you can easily install full extension and side mount drawer slides in no time. Let’s take a closer look at how to use this handy tool!
Summary: Kreg drawer slides are a great way to add a little extra convenience to your projects. This how-to guide will teach you how to use the Kreg drawer slide jig to make the process easier.
Step by Step Guide: How to Use Kreg Drawer Slide Jig
Step 1: Position the Drawer Slide Jigs.
For proper drawer slide installation, you’ll need to position the jigs on either side of the drawer box. The jigs should be flush with the top and bottom edges of the drawer box and the front edge. If the drawer box is not flush with the jigs, the drawer slides will not be level. When everything is lined up correctly, clamp the jigs in place.
Step 2: Drill the Holes for the Drawer Slides.
With the drawer slide jigs properly positioned, you can now drill the holes for the drawer slides. The holes should be drilled at a depth that is half the thickness of the drawer slide. For most drawer slides, this will be about 1 inch deep. Once the holes are drilled, remove the clamps and jigs.
Step 3: Attach the Drawer Slides to the Drawer Box.
You can now attach the drawer slides to the drawer box with the holes drilled. Start by attaching the brackets with the drawer slides to the drawer box. These brackets need to be attached so that the drawer slide is level with the top of the drawer box. Once the brackets are in place, you can then attach the drawer slide to the bracket. Again, ensure the drawer slide is level before attaching it to the bracket.
Step 4: Attach the Drawer Front to the Drawer Slide.
With the drawer slide attached to the drawer box, you can now attach the drawer front to the drawer slide. Start by aligning the holes on the drawer front with the holes on the drawer slide. Once everything is lined up, insert screws into the holes and tighten them. Be careful not to over-tighten the screws, as this can strip the holes or damage the drawer front.
Step 5: Attach the Drawer Pull.
After installing the drawer slide, it’s time to attach the drawer pull. The Kreg Drawer Slide Jig makes this easy, as well. Just align the jig with the holes in the drawer slide, and drill through the jig and into the drawer pull. Then, use screws to secure the drawer pull to the slide. If the drawer pull has a lip, ensure it’s facing the right direction before you attach it.
Step 6: Reposition the Jigs.
Now that the drawer slide is installed, you can reposition the jigs on either side of the box. The jigs should be flush with the top and bottom edges of the drawer box and the front edge. If the drawer box is not flush with the jigs, the drawer slides will not be level. When everything is lined up, tighten the jigs in place.
Step 7: Measure and Cut the Slides.
Now that the jigs are in place, you can measure and cut the slides to size. First, measure the distance between the two jigs. Then, add 1/8″ to that measurement. This will be the length of the drawer slides. Next, use a hacksaw or miter saw to cut the slides. If you think the cuts may not be perfectly straight, use a file to even them out.
Step 8: Test the Drawer.
Once everything is cut to size and installed, it’s time to test the drawer. First, open and close the drawer a few times to ensure everything is working correctly. If the drawer seems a little stiff, you can adjust the screws on the brackets until it opens and closes smoothly. When the drawer operates smoothly, you’re ready to move on to the next step.
Step 9: Attach the Knobs or Pulls.
The final step is to add the knobs or pulls to the drawer fronts. Just align the holes on the knob or pull with the holes on the drawer front, and screw them in place. Be careful not to over-tighten the screws, as this can strip the holes or damage the drawer fronts. And that’s it! You’ve now installed your very own Kreg Drawer Slide Jig. With this jig, you can easily install drawer slides in any project.
Some Helpful Tips and Suggestions
Here we have given tips on how to use kreg drawer slide jig.
- If you’re unsure where to drill the holes for the drawer slides, consult the instructions with the jig.
- When attaching the drawer slides to the brackets, be careful not to over-tighten the screws. This can strip the holes or damage the drawer slides.
- If you want to attach the drawer slides to the drawer boxes before attaching them to the brackets, you can do so by temporarily removing the stop block from the jig.
- When Installing the drawer slides, follow the manufacturer’s instructions.
- When attaching the drawer fronts, be careful not to over-tighten the screws. This can strip the holes or damage the drawer fronts.
- Test the drawer slides before installation to ensure a proper fit.
- When choosing the location for the drawer slides, allow enough clearance for the drawer to open and close smoothly.
How Do Drawer Slide Jigs Work?
Drawer slide jigs are tools that help you to install drawer slides with ease. With a drawer slide jig, you can easily align the holes on the drawer front with the holes on the drawer slide. Once everything is lined up, insert screws into the holes and tighten them.
Be careful not to over-tighten the screws, as this can strip the threading and make it difficult to remove the drawer later. Most drawer slide jigs come with an Allen key or hex wrench to tighten the screws. You can use a Phillips head screwdriver if you don’t have an Allen key or hex wrench.
Drawer slide jigs typically have a stop block that prevents you from inserting the screws too far into the drawer slide. There are a few different types of drawer slide jigs available on the market, but they all work in the same way. When choosing a drawer slide jig, make sure it is compatible with the type of drawer slides you are using.
Can Drawer Slides Be Shorter Than Drawers?
Yes, drawer slides can be shorter than drawers. This is useful when you want to make something small such as a flute, out of wood. The Kreg Drawer Slide Jig is a tool that allows you to measure and cut your drawer slides so they fit just right.
This jig makes it easy to make sure that your drawers will open and close smoothly, even if they are shorter than the drawers themselves! Make sure that the slides you buy are long enough for your project.
What To Look for When Choosing Drawer Slide Jig?
The Kreg drawer slide jig is one of the most popular and versatile jigs available on the market. However, there are a few things you should look for when choosing a drawer slide jig to ensure you get the most out of your purchase. First, consider the size of your project. The Kreg drawer slide jig is designed for use with drawer slides at least 18 inches long.
You may want to consider a different jig if you have a smaller project. Second, consider the type of drawer slide you will be using. The Kreg drawer slide jig is designed with full extension drawer slides. If you are using a different type of drawer slide, you may want to consider a different jig.
Third, consider the depth of your drawer. The Kreg drawer slide jig is designed for use with drawers at least 6 inches deep. You may want to consider a different jig if you have a shallower drawer. Finally, make sure that the jig you choose is compatible with the drawer slides you intend to use. If the jig is not compatible with the drawer slides, it may damage the slides or the jig itself.
Final Words
Drawer Slide Jig is an easy-to-use tool that makes drawer construction quick and accurate. It can be used with either a Kreg Pocket Hole jig or a Kreg face clamp. The Drawer Slide Jig ensures perfect placement of the drawer slides on both sides of the box, resulting in smooth, quiet operation. The Drawer Slide Jig comes with detailed instructions, making it simple for anyone to use. The jig is also adjustable to fit various drawer sizes.
Construction of drawers using the Drawer Slide Jig is fast and easy, saving time and frustration compared to other methods such as measuring and marking each side of the drawer independently. In addition, the Drawer Slide Jig ensures accuracy and consistency, making it the perfect tool for anyone building drawers. We hope this guide was helpful on how to use kreg drawer slide jig! If you have any questions or want to know more, feel free to comment below!
